奧林巴斯F114水浸搜尋管；奧林巴斯F114水浸搜尋管探頭；奧林巴斯F114水浸搜尋管；奧林巴斯F114水浸搜尋管；奧林巴斯F114**代理價格優惠；奧林巴斯F114銷售專線13530838910
奧林巴斯F114水浸搜尋管（F114）
奧林巴斯F114水浸搜尋管（F114）
奧林巴斯F114水浸搜尋管（F114）
奧林巴斯F114水浸搜尋管（F114）
奧林巴斯F114水浸搜尋管（F114）
奧林巴斯F114水浸搜尋管（F114）
特殊水浸探頭
Immersion special transducers refer to a variety of transducers that conduct many specific applications such as measuring wall thickness, inspection of aluminum plating, or multi-element array flaw detection.This group contains the following transducer types: side looking case, paintbrush, i-R style and XMS.
Side Looking Immersion Transducers
-
Ideal for measuring wall thicknesses of pipe where access to the outer diameter is limited
-
Small outer diameter allows for greater accessibility in tight spaces than standard immersion transducers with reflector mirrors
-
Sound exit point is located at a 90° angle relative to the straight Microdot ® connector
-
Probe extensions such as the F211 are available to lengthen the standard design
Note: All above side looking immersion transducers have straight Microdot connectors.
Transducer Configurator
*Please select a specific focus between min max.
**If a focus is required, select a focal length between min max
To view point target foci, click here.
i-R Style Housings
0.50 inches (10 mm) element diameters in 0.75 inches (19 mm) x 0.75 inches (19 mm) rectangular housings with side mount (right angle), UHF connectors, and 303 stainless steel case housings are available.
Transducer Configurator
*To view transducer point target focus, click here.
Extra Miniature (XMS) Transducer
The XMS transducer is an extremely small 10 MHz immersion transducer with a 3 mm (0.118") diameter by 3 mm (0.118") long case. This transducer is ideal for extremely tight access areas or for multi-element array flaw detection. The transducer assembly has a special connector attached to the 1 m (38") long potted cable. An adaptor is also available to interface with most commercial ultrasonic equipment.
水浸式探頭附件
水浸式探頭附件有助于進行水浸應用并發揮水浸檢測技術。這些附件包括起泡器、水浸箱、發射鏡和搜尋管
Reflector Mirrors
-
Directs sound beam when a straight-on inspection is not possible
-
Standard mirrors provide a 90° reflection of the sound beam
Note: Contact us for other reflected angles.
-
Allows for immersion testing when complete immersion of parts is not desirable or possible
-
Designed to maintain a consistent, low volume flow of water
RBS-1 Immersion Tank
RBS-1 immersion tank is designed to simplify testing measurements using immersion techniques. It consists of a clear acrylic tank, a submersible pump and a transducer fixture in a single, portable unit. The pump feeds an adjustable stream of water to a bubbler mounted in the fixture, providing a water column to couple sound from an immersion transducer into the test piece. It is ideal for offline thickness measurements on metal, glass and plastic products such as small containers, pipe or tubing, sheets or plates or machined parts.
Clear Acrylic Tank
-
5.5 x 12 x 8 inches (140 x 305 x 200 mm)
-
0.83 gallon (3.1 liter) capacity
Pump
-
Up to 0.25 gallons (0.9 liters) per minute
-
115 or 230 V, 30 Watt (voltage range 90 to 135 VAC), 50 to 60 Hz
-
Submersible (ground fault interrupter circuit recommended)
Handheld Bubbler Transducer Assembly
Handheld bubbler transducers are available in either 20 MHz (V316B) or 10 MHz (V312B). They are immersion transducers that screw onto a bubbler assembly (B120) which has a replaceable stainless steel tip and a water feed tube. They offer high resolution and easy access inspection of thin materials. The V316B and bubbler combination can resolve thicknesses down to 0.008" (0.2 mm).
Immersion Search Tubes
-
Provides a quick and easy way to fixture and manipulate immersion transducers